Network Working Group                                B. Clouston, Editor
Request for Comments: 2232                                 Cisco Systems
Category: Standards Track                               B. Moore, Editor
                                                         IBM Corporation
                                                           November 1997


                     Definitions of Managed Objects
                          for DLUR using SMIv2


Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1997).  All Rights Reserved.

Table of Contents

   1.     Status of this Memo  ....................................  1
   2.     Introduction  ...........................................  1
   3.     The SNMP Network Management Framework  ..................  2
   4.     Overview  ...............................................  2
   4.1      DLUR MIB structure ....................................  3
   5.     Definitions  ............................................  5
   6.     Acknowledgments  ........................................ 18
   7.     References  ............................................. 19
   8.     Security Considerations  ................................ 19
   9.     Authors' Addresses  ..................................... 20
   10.    Full Copyright Statement ................................ 21

2.  Introduction

   This memo defines a portion of the Management Information Base (MIB)
   for use with network management protocols in the Internet community.
   In particular, it defines objects for monitoring and controlling
   network devices with DLUR (Dependent LU Requester) capabilities.
   This memo identifies managed objects for the DLUR protocol.







Clouston & Moore            Standards Track                     [Page 1]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


3.  The SNMP Network Management Framework

   The SNMP Network Management Framework consists of several components.
   For the purpose of this specification, the applicable components of
   the Framework are the SMI and related documents [1, 2, 3], which
   define the mechanisms used for describing and naming objects for the
   purpose of management.

   The Framework permits new objects to be defined for the purpose of
   experimentation and evaluation.

4.  Overview

   This document identifies objects for monitoring the configuration and
   active characteristics of devices with DLUR capabilities.  Dependent
   LU requester/server (DLUR/S) is an extension to the Advanced Peer-
   to-Peer Networking (APPN) architecture that provides dependent LU
   services in APPN networks.  See the SNANAU APPN MIB [4] for
   management of APPN networks.

   The base APPN architecture only provided for transport of data
   between independent logical units (LUs).  However, customers have an
   enormous investment in applications based on dependent LU types.
   DLUR/S provides for support of dependent LU sessions in an APPN
   network.

   A dependent LU server (DLUS) is an APPN node that provides System
   Services Control Point (SSCP) services over an APPN network to remote
   secondary dependent LUs by using SSCP-PU (physical unit) and SSCP-LU
   sessions whose flows are encapsulated on LU 6.2 session flows between
   the DLUS node and the appropriate dependent LU requester (DLUR) node.
   The secondary dependent LUs may be local to the DLUR node, or in
   adjacent type 2.0 or 2.1 nodes.

   The LU 6.2 control sessions between a DLUS node and a DLUR node are
   referred to as a CPSVRMGR pipe.  CPSVRMGR refers to the mode used for
   the sessions.

   In this document, we describe DLUR managed objects.

   The DLUR terms and overall architecture are described in [5].

   Highlights of the management functions supported by the DLUR MIB
   module include the following:







Clouston & Moore            Standards Track                     [Page 2]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


   o    Identifying the node's DLUR capabilities

   o    Displaying the physical units (PUs) this node is supporting

   o    Identification of Dependent LU Servers

   o    Displaying the state of control sessions to Dependent LU
        Servers.

   This MIB module does not support:

   o    Management of dependent LU servers

   o    Configuration of DLUR nodes.

   o    Changing the state of control session to the DLUS

   o    Displaying the dependent LUs this node is supporting

   o    Traps.  The APPN MIB contains a trap for Alert conditions that
        may affect DLUR resources.  The value for the affectedObject
        object contained in the alertTrap is determined by the
        implementation.  It may contain a VariablePointer from the DLUR
        MIB.  The APPN/DLUR Alerts are defined in [6].

4.1.  DLUR MIB Structure

   Although DLUR is an extension to APPN, the DLUR MIB relies very
   little upon the APPN MIB.  The dlurNodeCpName object in this MIB has
   the same value as the appnNodeCpName object in the APPN MIB.  If the
   dlurPuLsName object in the MIB has the same value as the appnLsName
   object in the APPN MIB, then the two objects are referring to the
   same link station.

   The DLUR MIB module contains the following collections of objects:

   o    dlurNodeInfo--objects representing the capabilities and
        architecture options supported by the DLUR implementation, as
        well as default primary and backup DLUSs.

   o    dlurPuInfo--objects describing the PUs that this APPN node is
        supporting with DLUR.

   o    dlurDlusInfo--objects describing the control sessions with
        DLUSs.

   These are described below in more detail.




Clouston & Moore            Standards Track                     [Page 3]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


4.1.1.  dlurNodeInfo group

   The dlurNodeInfo group consists of the following objects and table:

   1) dlurNodeCapabilities group

   These objects represent the capabilities and options of the DLUR
   implementation, such as the release level of the implementation

   2) dlurDefaultDefBackupDlusTable

   This table identifies the list of defined backup DLUSs for all PUs
   served by this DLUR, if there is no specific DLUS backup list for the
   PU.  The list is in descending order of preference as a backup DLUS.

4.1.2.  dlurPuInfo group

   The dlurPuInfo group consists of the following tables:

   1) dlurPuTable

   This table has an entry for each PU this node is supporting via DLUR,
   including the locally known name, the SSCP supplied name (if known),
   and the PU status.

   2) dlurPuDefBackupDlusTable

   This table contains the backup DLUS list defined on a PU basis.  The
   table has an entry for each specifically defined backup DLUS on each
   PU.  The first index to the entry is the PU name, which organizes the
   table by PU name. The second index is a ranking which further sorts
   the table in descending order of preference as a backup DLUS for the
   PU.

   If a PU name is not found in this table, the
   dlurDefaultDefBackupDlusNameTable is used as a backup list for that
   PU.

4.1.3.  dlurDlusInfo group

   This group consists of the following table:

   1) dlurDlusTable

   This table contains information about the control sessions (CPSVRMGR
   pipes) with the DLUS, including the control point (CP) name of the
   DLUS and the status of the control session.




Clouston & Moore            Standards Track                     [Page 4]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


5.  Definitions

APPN-DLUR-MIB DEFINITIONS ::= BEGIN

IMPORTS
        DisplayString, TruthValue
                FROM SNMPv2-TC

        OBJECT-TYPE, MODULE-IDENTITY, Unsigned32
                FROM SNMPv2-SMI

        MODULE-COMPLIANCE, OBJECT-GROUP
                FROM SNMPv2-CONF

        snanauMIB
                FROM SNA-NAU-MIB

        SnaControlPointName
                FROM APPN-MIB;

dlurMIB MODULE-IDENTITY
        LAST-UPDATED  "9705101500Z"
        ORGANIZATION  "IETF SNA NAU MIB WG / AIW APPN/HPR MIBs SIG"
        CONTACT-INFO

                "
                        Bob Clouston
                        Cisco Systems
                        7025 Kit Creek Road
                        P.O. Box 14987
                        Research Triangle Park, NC 27709, USA
                        Tel:    1 919 472 2333
                        E-mail: clouston@cisco.com

                        Bob Moore
                        IBM Corporation
                        800 Park Offices Drive
                        RHJA/664
                        P.O. Box 12195
                        Research Triangle Park, NC 27709, USA
                        Tel:    1 919 254 4436
                        E-mail: remoore@ralvm6.vnet.ibm.com
                "
      DESCRIPTION
                "This is the MIB module for objects used to manage
                network devices with DLUR capabilities.  This MIB
                contains information that is useful for managing an APPN
                product that implements a DLUR (Dependent Logical Unit



Clouston & Moore            Standards Track                     [Page 5]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


                Requester).  The DLUR product has a client/server
                relationship with an APPN product that implements a DLUS
                (Dependent Logical Unit Server)."

::= { snanauMIB 5 }
-- snanauMIB ::= { mib-2 34 }

-- *********************************************************************
-- Textual Convention
-- *********************************************************************
-- SnaControlPointName is imported from the APPN MIB

-- *********************************************************************
  dlurObjects OBJECT IDENTIFIER ::= { dlurMIB 1 }
-- *********************************************************************


dlurNodeInfo OBJECT IDENTIFIER ::= { dlurObjects 1 }
-- *********************************************************************
-- DLUR Capabilities of the node
--
--  This group represents the capabilities and options of the DLUR
--  implementation.
-- *********************************************************************
dlurNodeCapabilities OBJECT IDENTIFIER ::= { dlurNodeInfo 1 }

dlurNodeCpName OBJECT-TYPE
      SYNTAX SnaControlPointName
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Administratively assigned network name for the APPN node where
          this DLUR implementation resides.  If this object has the same
          value as the appnNodeCpName object in the APPN MIB, then the
          two objects are referring to the same APPN node."

      ::= { dlurNodeCapabilities 1 }

dlurReleaseLevel OBJECT-TYPE
      SYNTAX DisplayString (SIZE (2))
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "The DLUR release level of this implementation.  This is the
          value that is encoded in the DLUR/DLUS Capabilites (CV 51).
          To insure consistent display, this one-byte value is encoded
          here as two displayable characters that are equivalent to a
          hexadecimal display.  For example, if the one-byte value as



Clouston & Moore            Standards Track                     [Page 6]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


          encoded in CV51 is X'01', this object will contain the
          displayable string '01'."

      ::= { dlurNodeCapabilities 2 }

dlurAnsSupport OBJECT-TYPE
      SYNTAX INTEGER {
                     continueOrStop(1),
                     stopOnly(2)
                     }
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Automatic Network Shutdown (ANS) capability of this node.

              -  'continueOrStop' indicates that the DLUR implementation
                 supports either ANS value (continue or stop) as
                 specified by the DLUS on ACTPU for each PU.

              -  'stopOnly' indicates that the DLUR implementation only
                 supports the ANS value of stop.

           ANS = continue means that the DLUR node will keep LU-LU
           sessions active even if SSCP-PU and SSCP-LU control sessions
           are interrupted.

           ANS = stop means that LU-LU sessions will be interrupted when
           the SSCP-PU and SSCP-LU sessions are interrupted."

      ::= { dlurNodeCapabilities 3 }

dlurMultiSubnetSupport OBJECT-TYPE
      SYNTAX TruthValue
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Indication of whether this DLUR implementation can support
          CPSVRMGR sessions that cross NetId boundaries."

      ::= { dlurNodeCapabilities 4 }

dlurDefaultDefPrimDlusName OBJECT-TYPE
      SYNTAX SnaControlPointName
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "The SNA name of the defined default primary DLUS for all of
          the PUs served by this DLUR.  This can be overridden for a



Clouston & Moore            Standards Track                     [Page 7]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


          particular PU by a defined primary DLUS for that PU,
          represented by the dlurPuDefPrimDlusName object."

      ::= { dlurNodeCapabilities 5 }

dlurNetworkNameForwardingSupport OBJECT-TYPE
      SYNTAX TruthValue
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Indication of whether this DLUR implementation supports
          forwarding of Network Name control vectors on ACTPUs and
          ACTLUs to DLUR-served PUs and their associated LUs.

          This object corresponds to byte 9. bit 3 of cv51."

      ::= { dlurNodeCapabilities 6 }

dlurNondisDlusDlurSessDeactSup OBJECT-TYPE
      SYNTAX TruthValue
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Indication of whether this DLUR implementation supports
          nondisruptive deactivation of its DLUR-DLUS sessions.
          Upon receiving from a DLUS an UNBIND for the CPSVRMGR pipe
          with sense data X'08A0 000B', a DLUR that supports this
          option immediately begins attempting to activate a CPSVRMGR
          pipe with a DLUS other than the one that sent the UNBIND.

          This object corresponds to byte 9. bit 4 of cv51."

      ::= { dlurNodeCapabilities 7 }

-- *********************************************************************
-- DLUR default defined backup DLUS table
-- *********************************************************************

dlurDefaultDefBackupDlusTable OBJECT-TYPE
      SYNTAX SEQUENCE OF DlurDefaultDefBackupDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "This table contains an ordered list of defined backup DLUSs
          for all of the PUs served by this DLUR.  These can be
          overridden for a particular PU by a list of defined backup
          DLUSs for that PU, represented by the
          dlurPuDefBackupDlusNameTable.  Entries in this table are



Clouston & Moore            Standards Track                     [Page 8]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


          ordered from most preferred default backup DLUS to least
          preferred."

      ::= { dlurNodeInfo 2 }

dlurDefaultDefBackupDlusEntry OBJECT-TYPE
      SYNTAX DlurDefaultDefBackupDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "This table is indexed by an integer-valued index, which
          orders the entries from most preferred default backup DLUS
          to least preferred."

      INDEX { dlurDefaultDefBackupDlusIndex }

      ::= { dlurDefaultDefBackupDlusTable 1 }

DlurDefaultDefBackupDlusEntry ::= SEQUENCE {
      dlurDefaultDefBackupDlusIndex      Unsigned32,
      dlurDefaultDefBackupDlusName       SnaControlPointName
                     }

dlurDefaultDefBackupDlusIndex OBJECT-TYPE
      SYNTAX Unsigned32 (1..4294967295)
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Index for this table.  The index values start at 1,
          which identifies the most preferred default backup DLUS."

      ::= { dlurDefaultDefBackupDlusEntry 1 }

dlurDefaultDefBackupDlusName OBJECT-TYPE
      SYNTAX SnaControlPointName
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Fully qualified name of a default backup DLUS for PUs served
          by this DLUR."

      ::= { dlurDefaultDefBackupDlusEntry 2 }

-- *********************************************************************
-- PU Information
--
--  The following table carries information about the PUs that this APPN
--  node is supporting via DLUR.



Clouston & Moore            Standards Track                     [Page 9]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


-- *********************************************************************
dlurPuInfo OBJECT IDENTIFIER ::= { dlurObjects 2 }

dlurPuTable OBJECT-TYPE
      SYNTAX SEQUENCE OF DlurPuEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Information about the PUs supported by this DLUR."

      ::= { dlurPuInfo 1 }

dlurPuEntry OBJECT-TYPE
      SYNTAX DlurPuEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Entry in a table of PU information, indexed by PU name."

      INDEX { dlurPuName  }

      ::= { dlurPuTable 1 }

DlurPuEntry ::= SEQUENCE {
      dlurPuName                  DisplayString,
      dlurPuSscpSuppliedName      DisplayString,
      dlurPuStatus                INTEGER,
      dlurPuAnsSupport            INTEGER,
      dlurPuLocation              INTEGER,
      dlurPuLsName                DisplayString,
      dlurPuDlusSessnStatus       INTEGER,
      dlurPuActiveDlusName        DisplayString,
      dlurPuDefPrimDlusName       DisplayString
                     }

dlurPuName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..17))
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Locally administered name of the PU."

      ::= { dlurPuEntry 1 }


dlurPuSscpSuppliedName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (0..17))
      MAX-ACCESS read-only



Clouston & Moore            Standards Track                    [Page 10]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


      STATUS current
      DESCRIPTION
          "The SNA name of the PU.  This value is supplied to a PU by the
          SSCP that activated it.  If a value has not been supplied, a
          zero-length string is returned."

      ::= { dlurPuEntry 2 }

dlurPuStatus OBJECT-TYPE
      SYNTAX INTEGER {
                      reset(1),
                      pendReqActpuRsp(2),
                      pendActpu(3),
                      pendActpuRsp(4),
                      active(5),
                      pendLinkact(6),
                      pendDactpuRsp(7),
                      pendInop(8),
                      pendInopActpu(9)
                     }
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Status of the DLUR-supported PU.  The following values are
          defined:

             reset(1)           -  reset
             pendReqActpuRsp(2) -  pending a response from the DLUS
                                   to a Request ACTPU
             pendActpu(3)       -  pending an ACTPU from the DLUS
             pendActpuRsp(4)    -  pending an ACTPU response from the PU
             active(5)          -  active
             pendLinkact(6)     -  pending activation of the link to a
                                   downstream PU
             pendDactpuRsp(7)   -  pending a DACTPU response from the PU
             pendInop(8)        -  the CPSVRMGR pipe became inoperative
                                   while the DLUR was pending an ACTPU
                                   response from the PU
             pendInopActpu(9)   -  when the DLUR was in the pendInop
                                   state, a CPSVRMGR pipe became active
                                   and a new ACTPU was received over it,
                                   before a response to the previous
                                   ACTPU was received from the PU."

      ::= { dlurPuEntry 3 }

dlurPuAnsSupport OBJECT-TYPE
      SYNTAX INTEGER {



Clouston & Moore            Standards Track                    [Page 11]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


                     continue(1),
                     stop(2)
                     }
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "The Automatic Network Shutdown (ANS) support configured for
          this PU.  This value (as configured by the network
          administrator) is sent by DLUS with ACTPU for each PU.

              -  'continue' means that the DLUR node will attempt to keep
                 LU-LU sessions active even if SSCP-PU and SSCP-LU
                 control sessions are interrupted.

              -  'stop' means that LU-LU sessions will be interrupted
                 when the SSCP-PU and SSCP-LU sessions are interrupted."

      ::= { dlurPuEntry 4 }

dlurPuLocation OBJECT-TYPE
      SYNTAX INTEGER {
                      internal(1),
                      downstream(2) }
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Location of the DLUR-support PU:
              internal(1)   - internal to the APPN node itself (no link)
              downstream(2) - downstream of the APPN node (connected via
                              a link)."

      ::= { dlurPuEntry 5 }

dlurPuLsName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (0..10))
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Administratively assigned name of the link station through
          which a downstream PU is connected to this DLUR.  A zero-length
          string is returned for internal PUs.  If this object has the
          same value as the appnLsName object in the APPN MIB, then the
          two are identifying the same link station."

      ::= { dlurPuEntry 6 }

dlurPuDlusSessnStatus OBJECT-TYPE
      SYNTAX INTEGER {



Clouston & Moore            Standards Track                    [Page 12]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


                      reset(1),
                      pendingActive(2),
                      active(3),
                      pendingInactive(4)
                     }
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Status of the control session to the DLUS identified in
          dlurPuActiveDlusName.  This is a combination of the separate
          states for the contention-winner and contention-loser sessions:

          reset(1)           - none of the cases below
          pendingActive(2)   - either contention-winner session or
                               contention-loser session is pending active
          active(3)          - contention-winner and contention-loser
                               sessions are both active
          pendingInactive(4) - either contention-winner session or
                               contention-loser session is pending
                               inactive - this test is made AFTER the
                               'pendingActive' test.

          The following matrix provides a different representation of
          how the values of this object are related to the individual
          states of the contention-winner and contention-loser sessions:

               Conwinner
               | pA | pI | A | X = !(pA | pI | A)
          C ++++++++++++++++++++++++++++++++++
          o pA | 2  |  2 | 2 | 2
          n ++++++++++++++++++++++++++++++++++
          l pI | 2  |  4 | 4 | 4
          o ++++++++++++++++++++++++++++++++++
          s A  | 2  |  4 | 3 | 1
          e ++++++++++++++++++++++++++++++++++
          r X  | 2  |  4 | 1 | 1
            ++++++++++++++++++++++++++++++++++
          "

      ::= { dlurPuEntry 7 }

dlurPuActiveDlusName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (0..17))
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "The SNA name of the active DLUS for this PU.  If its length
          is not zero, this name follows the SnaControlPointName textual



Clouston & Moore            Standards Track                    [Page 13]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


          convention.  A zero-length string indicates that the PU does
          not currently have an active DLUS."

      ::= { dlurPuEntry 8 }

dlurPuDefPrimDlusName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (0..17))
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "The SNA name of the defined primary DLUS for this PU, if one
          has been defined.  If present, this name follows the
          SnaControlPointName textual convention.  A zero-length string
          indicates that no primary DLUS has been defined for this PU, in
          which case the global default represented by the
          dlurDefaultDefPrimDlusName object is used."

      ::= { dlurPuEntry 9 }

-- *****************************************
-- Defined backup DLUS table for a PU
-- *****************************************

dlurPuDefBackupDlusTable OBJECT-TYPE
      SYNTAX SEQUENCE OF DlurPuDefBackupDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "This table contains an ordered list of defined backup DLUSs
          for those PUs served by this DLUR that have their own defined
          backup DLUSs.  PUs that have no entries in this table use the
          global default backup DLUSs for the DLUR, represented by the
          dlurDefaultDefBackupDlusNameTable.  Entries in this table are
          ordered from most preferred backup DLUS to least preferred for
          each PU."

      ::= { dlurPuInfo 2 }

dlurPuDefBackupDlusEntry OBJECT-TYPE
      SYNTAX DlurPuDefBackupDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "This table is indexed by PU name and by an integer-valued
          index, which orders the entries from most preferred backup DLUS
          for the PU to least preferred."

      INDEX { dlurPuDefBackupDlusPuName,



Clouston & Moore            Standards Track                    [Page 14]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


              dlurPuDefBackupDlusIndex }

      ::= { dlurPuDefBackupDlusTable 1 }

DlurPuDefBackupDlusEntry ::= SEQUENCE {
      dlurPuDefBackupDlusPuName          DisplayString,
      dlurPuDefBackupDlusIndex           Unsigned32,
      dlurPuDefBackupDlusName            SnaControlPointName
                     }

dlurPuDefBackupDlusPuName OBJECT-TYPE
      SYNTAX DisplayString (SIZE (1..17))
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Locally administered name of the PU.  If this object has the
          same value as the dlurPuName object, then the two are
          identifying the same PU."

      ::= { dlurPuDefBackupDlusEntry 1 }

dlurPuDefBackupDlusIndex OBJECT-TYPE
      SYNTAX Unsigned32 (1..4294967295)
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "Secondary index for this table.  The index values start at 1,
          which identifies the most preferred backup DLUS for the PU."

      ::= { dlurPuDefBackupDlusEntry 2 }

dlurPuDefBackupDlusName OBJECT-TYPE
      SYNTAX SnaControlPointName
      MAX-ACCESS read-only
      STATUS current
      DESCRIPTION
          "Fully qualified name of a backup DLUS for this PU."

      ::= { dlurPuDefBackupDlusEntry 3 }

-- *********************************************************************
--               DLUS Control Sessions (CPSVRMGR Pipes)
--
--  This table contains information about DLUS control sessions, also
--  known as CPSVRMGR pipes.  Although DLUR uses a pair of CPSVRMGR
--  sessions for communication, for the purpose of status, information
--  about these two sessions is combined to yield a single status for the
--  requester/server connection.



Clouston & Moore            Standards Track                    [Page 15]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


-- *********************************************************************

dlurDlusInfo OBJECT IDENTIFIER ::= { dlurObjects 3 }

dlurDlusTable OBJECT-TYPE
      SYNTAX SEQUENCE OF DlurDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
           "Information about DLUS control sessions."

      ::= { dlurDlusInfo 1}

dlurDlusEntry OBJECT-TYPE
      SYNTAX DlurDlusEntry
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
           "This entry is indexed by the name of the DLUS."

      INDEX { dlurDlusName }

      ::= { dlurDlusTable 1 }

DlurDlusEntry ::= SEQUENCE {
      dlurDlusName          SnaControlPointName,
      dlurDlusSessnStatus   INTEGER
                     }

dlurDlusName OBJECT-TYPE
      SYNTAX SnaControlPointName
      MAX-ACCESS not-accessible
      STATUS current
      DESCRIPTION
          "The SNA name of a DLUS with which this DLUR currently has a
          CPSVRMGR pipe established."

      ::= { dlurDlusEntry 1 }

dlurDlusSessnStatus OBJECT-TYPE
      SYNTAX INTEGER {
                      reset(1),
                      pendingActive(2),
                      active(3),
                      pendingInactive(4)
                     }
      MAX-ACCESS read-only
      STATUS current



Clouston & Moore            Standards Track                    [Page 16]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


      DESCRIPTION
          "Status of the CPSVRMGR pipe between the DLUR and this DLUS.
          This is a combination of the separate states for the
          contention-winner and contention-loser sessions:

          reset(1)           - none of the cases below
          pendingActive(2)   - either contention-winner session or
                               contention-loser session is pending active
          active(3)          - contention-winner and contention-loser
                               sessions are both active
          pendingInactive(4) - either contention-winner session or
                               contention-loser session is pending
                               inactive - this test is made AFTER the
                               'pendingActive' test.

          The following matrix provides a different representation of
          how the values of this object are related to the individual
          states of the contention-winner and contention-loser sessions:

               Conwinner
               | pA | pI | A | X = !(pA | pI | A)
          C ++++++++++++++++++++++++++++++++++
          o pA | 2  |  2 | 2 | 2
          n ++++++++++++++++++++++++++++++++++
          l pI | 2  |  4 | 4 | 4
          o ++++++++++++++++++++++++++++++++++
          s A  | 2  |  4 | 3 | 1
          e ++++++++++++++++++++++++++++++++++
          r X  | 2  |  4 | 1 | 1
            ++++++++++++++++++++++++++++++++++
          "

      ::= { dlurDlusEntry 2 }

-- ***************************************************************
-- Conformance information
-- ***************************************************************

dlurConformance       OBJECT IDENTIFIER ::= { dlurMIB 2 }

dlurCompliances       OBJECT IDENTIFIER ::= { dlurConformance 1 }
dlurGroups            OBJECT IDENTIFIER ::= { dlurConformance 2 }

-- Compliance statements

dlurCompliance MODULE-COMPLIANCE
      STATUS current
      DESCRIPTION



Clouston & Moore            Standards Track                    [Page 17]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


          "The compliance statement for the SNMPv2 entities which
          implement the DLUR MIB."

      MODULE -- this module

--    Unconditionally mandatory groups
      MANDATORY-GROUPS  { dlurConfGroup }

      ::= { dlurCompliances 1 }

-- Units of conformance
dlurConfGroup OBJECT-GROUP
      OBJECTS {
               dlurNodeCpName,
               dlurReleaseLevel,
               dlurAnsSupport,
               dlurMultiSubnetSupport,
               dlurNetworkNameForwardingSupport,
               dlurNondisDlusDlurSessDeactSup,
               dlurDefaultDefPrimDlusName,
               dlurDefaultDefBackupDlusName,
               dlurPuSscpSuppliedName,
               dlurPuStatus,
               dlurPuAnsSupport,
               dlurPuLocation,
               dlurPuLsName,
               dlurPuDlusSessnStatus,
               dlurPuActiveDlusName,
               dlurPuDefPrimDlusName,
               dlurPuDefBackupDlusName,
               dlurDlusSessnStatus
              }
      STATUS current
      DESCRIPTION
          "A collection of objects providing information on an
          implementation of APPN DLUR."

      ::= { dlurGroups 1 }

-- end of conformance statement

END

6.  Acknowledgments

   This MIB module is the product of the IETF SNA NAU MIB WG and the AIW
   APPN/HPR MIBs SIG.




Clouston & Moore            Standards Track                    [Page 18]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


7.  References

   [1]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Structure of Management Information for version 2 of
        the Simple Network Management Protocol (SNMPv2)", RFC 1902,
        January 1996.

   [2]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Textual Conventions for Version 2 of the Simple
        Network Management Protocol (SNMPv2)", RFC 1903, January 1996.

   [3]  Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
        "Conformance Statements for Version 2 of the Simple
        Network Management Protocol (SNMPv2)", RFC 1904, January 1996.

   [4]  Clouston, B., and B. Moore, "Definition of Managed Objects for
        APPN", RFC 2155, June 1997.

   [5]  IBM, Systems Network Architecture Advanced Peer-to-Peer
        Networking Dependent LU Requester Architecture Reference,
        Version 1.2, SV40-1010-01, December 1995.

   [6]  IBM, SNA/MS Formats, GC31-8302-00.

8.  Security Considerations

   In most cases, MIBs are not themselves security risks; if SNMP
   security is operating as intended, the use of a MIB to view
   information about a system, or to change some parameter at the
   system, is a tool, not a threat.

   None of the read-only objects in the DLUR MIB reports a password,
   user data, or anything else that is particularly sensitive.  Some
   enterprises view their network configuration itself, as well as
   information about network usage and performance, as corporate assets;
   such enterprises may wish to restrict SNMP access to most of the
   objects in the MIB.

   There are no read-write objects in the DLUR MIB.












Clouston & Moore            Standards Track                    [Page 19]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


9.  Authors' Addresses

   Bob Clouston
   Cisco Systems
   7025 Kit Creek Road
   P.O. Box 14987
   Research Triangle Park, NC 27709, USA

   Phone: +1 919 472 2333
   EMail: clouston@cisco.com


   Bob Moore
   IBM Corporation
   800 Park Offices Drive
   CNMA/664
   P.O. Box 12195
   Research Triangle Park, NC 27709, USA

   Phone: +1 919 254 4436
   EMail: remoore@ralvm6.vnet.ibm.com






























Clouston & Moore            Standards Track                    [Page 20]


RFC 2232         Managed Objects for DLUR using SMIv2      November 1997


10.  Full Copyright Statement

   Copyright (C) The Internet Society (1997).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
























Clouston & Moore            Standards Track                    [Page 21]